江蘇春晨電纜有限公司生產春晨JFEYH高壓電機引接線JFEYH高壓電機引出線，

刀開關的圖形符號和文字符號

The graphic symbols and characters of the knife switch

刀開關的圖形符號和文字符號刀開關的圖形符號和文字符號如圖所示。圖 刀開關的圖形符號和文字符號

The graphic symbols of the knife switch and the graphic symbols and character symbols of the word symbol knife switch are shown as shown in the diagram. Graphic symbols and literal symbols of a knife switch

2017-10-28 07:08

2017-10-28 07:08

如何計算變壓器鐵芯截面積春晨JFEYH高壓電機引接線JFEYH高壓電機引出線

How to calculate the intercepting area of transformer core

如何計算變壓器鐵芯截面積小型單相變壓器多采用殼式鐵芯，變壓器鐵芯截面積與變壓器的容量有關，一般按下列經驗公式計算。 A=k√s(cm2)式中，s為變壓器的容量；k為系數。硅鋼片的k值見表。表 鐵芯凈截面系數的經驗數據根據計算得到的A值，可 ...

How to calculate the cross-sectional area of transformer core is mainly used in small single-phase transformers. The core area of transformer is related to the capacity of transformer. It is usually calculated according to the following empirical formula. A=k root s (cm2) type, s for transformer capacity; K coefficient. The K value of silicon steel sheet is shown in the table. The empirical data of the net section coefficient of the iron core can be calculated according to the calculated A value.

2017-10-28 07:05

2017-10-28 07:05

變壓器的基本結構和工作原理

Basic structure and working principle of transformer

變壓器的基本結構是由鐵芯和繞組（線圈）組成的。變壓器鐵芯是由兩面涂有絕緣漆的硅鋼片疊裝而成的。繞組是繞在鐵芯上的兩個匝數不等的線圈，與電源相連的繞組稱為一次繞組，與負載相連的繞組稱為二次繞組。變壓器就 ...

The basic structure of a transformer consists of a core and a winding (coil). The iron core of the transformer is made up of two silicon steel sheets coated with insulating varnish. A winding is a coil of two turns around an iron core. The winding connected to the power is called a primary winding, and the winding connected to the load is called the two winding. The transformer is...

2017-10-28 07:04

2017-10-28 07:04

電氣設備選擇春晨JFEYH高壓電機引接線JFEYH高壓電機引出線

Selection of electrical equipment

電氣設備選擇電氣設備選擇的一般條件：1.按正常工作方式選擇電氣設備；2.按短路方式進行設備的校驗。一、按正常工作方式選擇電氣設備1、選擇額定電壓：電氣設備耐壓不得低于安裝位置的可能工作電壓。一般電氣設備的 ...

Electrical equipment selection of the general conditions for selection of electrical equipment: 1. according to the normal mode of selection of electrical equipment; 2. according to the mode of short-circuit verification of the equipment. 1. Select the electrical equipment 1 according to the normal working way and select the rated voltage: the maximum voltage of the electrical equipment must not be lower than the maximum possible working voltage of the installation position. The highest electric equipment is the highest.

2017-10-27 11:53

2017-10-27 11:53

照明線需要裝漏電保護？聽老師傅一講完，我才知道我家就裝錯了

Does the lighting line need leakage protection? After listening to the teacher, I knew that my house was wrong.

照明線需要裝漏電保護？聽老師傅一講完，我才知道我家就裝錯了裝修的時候，電工會幫家里做好漏電保護裝置。大家應該都知道，漏電保護既是開關也是裝置。它在一個家里的作用之大不用多說。如果家里泄漏電的話，它就會自動斷開電源，保護電路，避免人體觸電。那么像家里照明燈需不 ...

Does the lighting line need leakage protection? After listening to the teacher, I knew that when my house was decorated, the electrician would help the home to do the leakage protection. It should be known that leakage protection is both a switch and a device. It doesn't have to say much about the role of a family. If the electricity is leaking at home, it will automatically disconnect the power, protect the circuit and avoid the electric shock of the human body. So like home lights need not...

2017-10-26 20:18

2017-10-26 20:18

三孔插座正確安裝方法

The correct installation method of socket

三孔插座正確安裝方法三孔插座上面孔為接地線，左邊是零線（N）右邊是火線（L）。 三孔插座是有專用的保護接零（地）插孔，在采用接零保護時，許多人僅在插座底內將此孔接線柱頭與引入插座內的那根零線直接相連，這是極為危險的。因為萬 ...

The correct installation method of socket socket hole above the ground, the left is the zero line (N) on the right line (L). There is a socket special protection to zero (ground) Jack, used in zero connection protection, many people only in the hole in the socket bottom wiring socket with the introduction of stigma that is directly connected to the zero line, it is extremely dangerous. Because of the ten thousand..